产品描述：

HENRY 131 瓷砖粘合剂是优选天然矿物原料和改性聚合物配制而成的水泥基粘合剂。该产品相对于传统的水泥砂浆更具有粘结力、施工便捷、薄贴工艺节省空间、减少材料损耗，其超强的粘结力使低吸水率的瓷砖铺贴更持久牢固。地面铺贴时，可以做到24小时上人行走。

 

产品特点：

● 良好的润湿性;

● 优异的粘结强度，防止砖脱落;

● 施工便捷，早强。

 

用法用量：

所有基层应平整、坚实、干净、无空鼓、无油污、蜡渍、脱模剂和其他松散物

1、将产品倒入清水中搅拌成膏状，注意要先加水后再倒入产品，搅拌时使用电动搅拌机；

2、混合比：25kg产品：5.2-5.5L清水。

3、充分搅拌均匀至无粉团，搅拌完成后需静置五分钟，再稍作搅拌后使用，更有利于增加粘结力。

4、用齿形刮刀将膏状瓷砖胶均匀涂布于粘贴面，并形成均匀条齿状。每次涂布面积不要太大，然后在晾置时间内铺贴瓷砖即可。

5、齿形刮刀的选择应根据工作面的平整度和瓷砖背面的凹凸程度而定。

6、砖背面和基面都粘满瓷砖粘合剂，保证施工质量。

 

参考用量：

● 约1.5kg/㎡/mm；具体用量随基层状况、所用齿形抹刀规格及瓷砖背面凹凸情况的不同有轻微差异。

 

注意事项：

1、该产品按参考比例加水即可使用，禁止参加其他材料；

2、施工温度为5-35℃；

3、混合比例可因基层、天气、施工条件等不同而做出适当调整；

4、搅拌好的粘合剂应在2小时内使用完毕，杜绝将已干结的粘合剂拌水使用；

5、铺贴施工完成后，需待粘合剂完全干固后，24小时后才可以进行下一步的填缝工作；

6、严禁无缝镶贴！砖与砖之间必须留有≧2㎜的缝隙；

7、在进行墙面铺贴时，注意做好临时固定措施。

8、室内施工高度应≤4m。

 

执行标准：JC/T 547-2017

 

储存运输：本品须存放于干燥、通风的室内环境，防潮、防水、防止暴晒，保质期为12个月。

 

包装：20KG、25KG/包

 

 

 

HENRY 131 Ceramic Tile Adhesive

Discription:

HENRY131 is a cement-based adhesive with natural mineral materials and modified polymers. Comparing with traditional cement mortar, this product has advantages of good adhesion, easy to use, environmental-friendly and safety. The thin paste method can save space and materials; the super adhesion make sure the tiles with low water absorption can be applied with more durability and firmness. being walkable 24h after the application on the floor.  

 

Features:

Good wettability;

Good adhesion, prevent tiles from falling off;

Easy to use, early strength

 

Application:

The backgrounds and surfaces to receive the tile must be clean, firm and free of dust, dirt, oil, grease, curing compounds, release agents and other barriers adhesion, as well as being strong enough to support the weight of the tiles being fixed.

1. The powder should be added into clean water in a clean container whilst stirring vigorously and mixed thoroughly to give easily worked mortar.

2. Mixing ratio: powder: water =25Kg: 5.2-5.5L;

3. Allow to stand for 3 minutes during the mixing, then restir the mortar thoroughly. This procedure can increase the bonding strength of the mortar.

4. Apply the mortar evenly on the surface of the substrate with a notched trowel and make sure to press the tiles into the freshly combed mortar in open time.

5. The type of notched trowel is depending on the substrate conditions and size of tiles.

6. The quality of application can be checked by unloading the tiles to see whether the substrate and the back of the tiles are full of mortar.

 

Notes:

1. Please following the mixing ratio, other materials should not be added during the mixing.

2. The application temperature is 5-35 ℃;

3. The water/powder ratio will vary depending on the substrate, weather and site condition;

4. The mortar should be applied within approx.2 hours. Do not reuse the dry mortar by adding water again;

5. Grouting may be allowed approximately 24 hours after the application;

6. Seamless application is forbidden, the width of tile joints should be ≧ 2mm 

7. Pay attention to provisional fixing measures during the wall application

8. Interior application height should be ≤ 4 m.

 

Coverage:

About 1.5kg/㎡/mm;The coverage will vary depending on substrate condition, application tools, tile type and application technique.

 

Standards: JC/T 547-2017

 

Storage& Shelf Life:

This product has a shelf life of approximately 12 months if stored in a dry, cool, ventilated place in original unopened packaging.

 

Package:20kg、25kg/bag