产品描述：

HENRY 522 柔性防水浆料粉料是由高强硅酸盐水泥、优质骨料、添加剂和聚合物乳液等原料精制而成。用于混凝土、水泥砂浆、地下室、露台及阳台、游泳池、储水池、浴室地面及厨房等防水抗渗工程，对于防水膜施工后需粘贴瓷砖，砂浆镘涂的场所特别适用。

 

产品特点：

● 能够覆盖毛细裂缝；

● 绿色环保，施工便捷；

● 易混合，可刷涂、滚涂；

● 附着力强，粘结强度高。

 

用法与用量：

基层处理：混凝土、砂浆基础面和砖体表面必须清洁、无油污及松散附着物，所有表面应尽量平整。施工前，若基础表面有吸水性，则应使其吸水至饱和，但不能有积水。

1、将B组份倒入干净的搅拌容器中，然后按照粉液比3:1的比例一边搅拌一边缓慢加入A组份，彻底搅拌至色泽一致。

2、用刷子或滚筒将浆料均匀地涂刷在处理好的基材上，根据使用环境涂刷2层或2层以上。

3、每做完1层，必须待其表干（约2～4小时）后，再做第2层，具体情况视基面的密实度以及当时的气温而定。如果在涂层已经固化时再做第2层，必须先用清水重新润湿表面。

4、养护：涂刷完后第二天起，建议用喷雾或湿布覆盖涂层2-3天再进行闭水试验；对于长期浸水环境，应待其空置两周后才盛水。用量：1.5-2.0kg/m²
 

执行标准：JC/T 2090-2011 Ⅰ型

 

储存运输：本品须存放于干燥、通风的室内环境，防潮、防水、防止暴晒，保质期为12个月。

 

包装： 25KG/包，7KG/桶，18KG/桶

 

 

 

 

HENRY 522 Flexible  Waterproofing Slurry

 

Description:

The product is a 2-component waterproof slurry made of high strength Portland cement, high quality aggregate, additives, polymer emulsion, fully meet the requirements of standard JC/T2090-2011(Type I), can be applied on concrete, cement mortar substrates in basement, terrace and balcony, swimming pool, storage pool, bathroom, kitchen and other waterproof areas, especially suitable for areas to be covered by tiles or mortar.

 

Features:

Environmental protection;

Easy to use;

Can be applied on slight cracks;

Excellent bonding strength.

 

Application:

Substrate Preparation: the surface to be coated should be dry, clean, sound and free from oil, grease, laitance and flaking paint. Make sure the surface is water saturated and with no water visible on the substrate with water absorbency.

1.Pour component B liquid into a clean mixer, then slowly add component A powder by mixing ratio of powder: liquid=3:1 while mixing. The mixing time should be 3-5 minutes.

2.Apply the slurry evenly to the substrate with a brush or roller, apply 2 or more layers depending on the condition.

3.The following coat should be applied when the previous coat is slightly dry and solid (but not fully dried), which generally takes 2-4 hours. Drying time will vary depending substrate and temperature condition. If the previous coat is fully dried, wet the surface before next application.

4.Maintenance: from the second day after application, it is recommended to cover the coating with wet cloth or water spray for 2-3 days before the closed water test. For long-term immersion area, the site should be maintained at least 2 weeks before being filled with water.

Coverage: 1.5-2.0kg/m²/ layer

 

Notes:

The application temperature condition should be 5-35℃.The open time of the product is approx.30 minutes. The application should not be carried out under the environment of direct sunlight or strong winds. Please follow the mixing ratio and do not add water into the mixture. The product can be only applied on a well-prepared, firm substrate. Tools should be cleaned by water immediately after application, dried product residues can be removed proper machine.

 

Standards: JC/T2090-2011 I

 

Storage& Shelf Life:

This product has a shelf life of approximately 12 months if stored in indoor temperature for 5-35°C in original unopened packaging, avoiding sun exposure or freeze.

 

Package:18 kg/barrel